Description
Axalta 300SF Food Grade Epoxy Floor Paint is a two pack, solvent free, high build coating for concrete floors.
- For new and old concrete floors subject to heavy mechanical wear and/or chemical attack, in areas such as the food processing, brewing, pharmaceutical and heavy engineering industries
- High gloss, easily cleaned finish
- Available in BS381C + RAL colours
- Resistant to water, oils, weak solutions of non-oxidising acids, alkali and salt solutions, and temporary splashes of oxidising acids and bleaches – VOC free
- Accepts light traffic after 16hrs @23°C (300µm dft)
- This 4.5 litre kit will cover approximately 9 – 14.85 mt ² (depending on application method, painting conditions, porosity & surface profile)
- This kit includes 4lt Epoxy paint & 500ml hardener.
- The mixing ratio is 4 parts paint to 1 parts hardener (4:1)
Technical Data | |
---|---|
Axalta ViterFloor 300 SF Epoxy Floor Paint | |
Volume Solids | 99 ± 1% (loss of trace volatiles may reduce figure) |
VOC Content | Does not contain VOC’s |
SG | 1.38-1.42 kg/lt mixed (may vary with colour) |
Storage Conditions | Store in dry, cool conditions and protect from frost |
Shelf Life | Minimum 12 months if stored as above in unopened containers |
Flash Point | Above 60°C |
Pot Life | 20-30 minutes when poured on the floor; approx. 15 minutes in the container |
Film Thickness Range & Coverage | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | Theoretical Coverage | |
Minimum* | 300 µm (0.30mm) | 300 µm | 3.3 m2/litre |
Maximum* | 500 µm (0.50mm) | 500 µm | 2.0 m2/litre |
*See Product Notes. Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated |
Drying Times | ||||
---|---|---|---|---|
Applied to 300 microns DFT | 23℃ | |||
Dust Dry | 6hrs | |||
Light Traffic | 16hrs | |||
Full Cure | 7 Days | |||
Recoating | Normal maximum 24 hrs* | |||
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation |
Surface Preparation
- All surfaces must be clean, dry, and free from grease, oil, laitance, dust and other contamination
- Apply over ViterFloor400 Primer/Sealer – consult relevant Product Data Sheet for details
Mixing Ratio:
- Base 2995 – 4 parts by volume (5 parts by wt.)
- Hardener 2995 101 – 1 part by volume (1 part by wt.)
Mixing Instructions:
- Components must be mixed thoroughly by using a mechanical mixer (with side scraper) before use
- Add hardener in the correct proportions and mix thoroughly for a minimum of 2 minutes
- Mix the material just before use, and consider the area to be coated and pot life of the material when deciding how many units are required
- Note: do not scrape or pour out remaining residues of mixed material from the bottom and sides of the container onto the floor, as this material may be incompletely mixed and cause ‘soft spots’ in the applied floor coating
- It is recommended that all material is stored at a temperature of approximately 20ºC for at least 24 hours prior to use, to aid mixing and application.
Application Methods
- This product is recommended for application by serrated or steel trowel, felt or mohair roller, with brush being used only where required to cut-in around edges or for very small areas
- Pour out the mixed ViterFloor 300 onto the primed floor and spread with a suitable trowel
- Level with a mohair or felt roller, wearing spiked shoes to walk across the wet coating
- Refer to Axalta Coating Systems Epoxy Application and Curing Notes
Reviews
There are no reviews yet.